Valves: Difference between revisions

From IBLS
Jump to navigation Jump to search
Line 68: Line 68:
* [http://discoverlivesteam.com/magazine/16/16.html "Valve Gear Conversion", Phil Heath, <i>DiscoverLiveSteam.com</i>]
* [http://discoverlivesteam.com/magazine/16/16.html "Valve Gear Conversion", Phil Heath, <i>DiscoverLiveSteam.com</i>]
* [http://www.chaski.org/homemachinist/viewtopic.php?f=8&t=100843 "Corliss valve material", <i>Chaski.org</i>]
* [http://www.chaski.org/homemachinist/viewtopic.php?f=8&t=100843 "Corliss valve material", <i>Chaski.org</i>]
* [http://www.billp.org/Dockstader/ValveGear.html "Steam Engine Valve Gear on the Computer", Charlie Dockstader]
* [http://www.modeng.johnbaguley.info/Valve%20Gears/Simulators.htm "Valve Gear Simulators"]
* [http://www.donashton.co.uk/html/downloads.html "Don Ashton's Steam Locomotive Valve Gears"]

Revision as of 18:17, 11 December 2017


by Charles A. Purinton

The Live Steamer, March-April 1950

CarlPurinton ValveDiagrams 1950.jpg

Valves and valve gears can be the making or the breaking of the performance of any engine. There are other things that enter the picture as well, but, if the valves and valve gear are right, the other conditions can be dealt with and usually corrected without too much trouble.

It could be that an explanation and a skwtch or two might be welcome. I realize that I am treading on dangerous ground here, as a complete answer to valve and valve gear problems takes a lifetime of study to master and a lot of technical study, in addition.

When talking about this subject, one will hear some of the terms mentioned, such as lap, lead, valve travel, steam ports, exhaust port, bridges and line in line. To a good many of the older (I do not mean in years) and more experienced Live-Steamers, these terms are clear and well understood. To the man building his first engine, and some of the more experienced ones as well, they are about as clear as mud and not too well understood.

Lap is the amount the steam edges of the valve overlap the steam ports when the valve is central. Its purpose is to allow the steam to be used expansively. This means less fuel and water is used.

Lead is the amount the valve has opened the steam port for admission when the piston is on a dead center. It is given for the purpose of getting the steam into the cylinder so that it will be there ready to push the piston as it passes the dead centers.

Valve Travel is the total distance that the valve moves in one direction and measured with the reverse lever in either full gear position. it should be equal to one lap plus one steam port times two. For example, if one lap is 1/8 inch and one steam port is 1/8 inch, then the total full gear travel should be one-half inch. It is important to know the total full gear valve travel so that the valve gear itself can be designed to give this full gear valve travel.

The steam ports, the exhaust port and the bridges are best explained by Sketch #1 and the Port Face. The bridges should be equal to the steam ports. The exhaust port should be at least twice the size of the steam ports, measured fore and aft.

Line and Line is a somewhat ambiguous term, as it is used in two different ways. Sometimes it is applied to a valve that has no lap. In this case, the steam edge of the valve and the steam port are line and line. Such a valve would permit steam to follow the piston its whole stroke and would be extremely wasteful.

It is my belief that this term is more commonly used in connection with the exhaust edges of the valve and the exhaust edge of the steam ports. This is the condition shown on Sketch #1. The valve cavity should always be this way, if it is a trifle more, it will help the steam to get out easily, and this is just as important as getting it in.

Square

From The Live Steamer, March-April 1950

What is meant by the term Square or Out of Square applying to a locomotive?

When an engine is Square it means that the valve setting is such that the four exhaust blasts, which occur with each revolution of drive wheels, are evenly spaced and of equal intensity. being Out of Square is the reverse of this condition and indicates some trouble with the valve gear (or valve setting).

Troubleshooting

Several issues can lead to a locomotive being out of square.

Valve Timing

See Valve Timing

Tumbler Rods

Paul Keiser posted on Chaski.org:

Setting the lifting arms on to the tumbling shaft. This is critical before you bore a #3 taper pin reamer to finalize the position. If one side is off, the block in the link will be off position from the other side and the choo choo will walk with a limp.

Grinding

Big C posted on Chaski.org

I have built several of the Allen Moguls and Ten Wheelers. When I would work up the cylinders, heads, steam chests, and covers, I would lap the heads to the cylinders with fine grade of Clover valve grinding compound. The steam chests and covers would be worked over a surface plate, e.g. a piece of broken window glass that I got out of an old railroad passenger car, along with a really fine grade of wet or dry sandpaper with a bit of kerosene. The parts would be assembled with no gaskets, just a little smear of non hardening permetex, and, of course, the necessary bolts needed to hold everything together.

References