IBLS Coupler and Safety Chain Standards

From IBLS
Revision as of 23:16, 9 February 2013 by Dnevil (talk | contribs) (→‎Layout)
Jump to navigation Jump to search

Layout

Couple and Safety Chain Layout
Scale Gauge Coupler/Chain Hook Height (CH) Chain Offset (CO) Hook Size Link SizeChain Length
3/4" 3-1/2" 2-1/4
1" 4-3/4" 2-7/8" +/- 1/4" 1-1/4" 0.11" 3-1/2" +/- 1/2"
1" 5" 3-1/4" +/- 1/4" 1-1/4" 0.11" 3-1/2" +/- 1/2"
1-1/2" 7-1/4" 4-7/16" +0" -3/16" 2-1/2" +/- 1/4" 1/4" 1/8"x1" welded6" +/- 1"
1-1/2" 7-1/2" 4-7/16" +0" -3/16" 2-1/2" +/- 1/4" 1/4" 1/8"x1" welded 6" +/- 1"
1.6" 7-1/2" 4-7/16" +0 -3/16" 2-1/2" +/- 1/4" 1/4" 1/8"x1" welded 6" +/- 1"
  • Safety Chain Data
    • Right hook is a captive hook
    • Left hook is an open hook
    • Hook Size refers to the diameter of the hook shank
    • Chains must pass over hooks
Safety chains and hooks in end-sill. From DiscoverLiveSteam.com

Tidbits From Chaski

From http://www.chaski.com/homemachinist

Carl B "ccvstmr"

ILS standard calls for two (2) 1/4" hooks at 2.5" distance from the centerline of the car. I set the hooks at 3" because I don't like to "crowd" the coupler. Eyebolts with 1/4x20 thread and various length shanks can be purchased at most hardware stores. The left hook is twisted open while the right hook is opened...the chain inserted...and the hook closed to make the chain captive. I would suggest putting hooks in a vise and using a crescent wrench to twist the hook open as much as needed to slip the chain on...and then close the eye bolt. Do not try to "unwind" the the hook loop and then squeeze it closed.
Example application of safety chains and hooks
Chains are 6" +/- 1". Chain material is 1/8" x 1" welded link...although 3/16" x 1" link would also do. The chain must fit over the chain hooks. Wire-wrap chain is not acceptable either.
One point that is often overlooked...is the method in which the the chain hooks are attached to the loco/car body. A screw-in eye-bolt hook is not acceptable, nor is a hook attached to an end-sill that is nailed to the end of the car. In other words, the hook attachment to the car body must be strong enough to withstand the forces transmitted through the chain(s) during a derailment. It is better to destroy the hook (straighten it out) instead of destroying your rolling stock or let your cars get away and be stopped by the next train that follows.
If anchoring hook in metal...drill a #7 hole and tap for a 1/4-20 thread. Use a nut on both sides to "lock" the eye bolt in place. If anchoring hook in wood...drill a 1/4" hole and again, use a nut on the face and back to hold in place. Do not use "lag" type eye bolts for wood. If you have a wood end sill...back it up with a well anchored piece of steel angle. If the equipment uncouples, you don't want the chains to yank the wooden sill off. btw...flange nuts look decent on the face...Nylok nuts on the back.
Another item to watch for...always make sure that safety chains are hooked at both ends...even if it's the last car of the train. A dragging chain will easily catch a turnout frog and/or heel block if you're not careful. The result...time to replace the chain hooks. Hope this helps.
Coupler height...most clubs have coupler height specs. Some follow IBLS, others are not far away. Usually the center of the coupler is set 4-1/4" to 4-7/16" over the rail head. Of course, as long as "out of spec" equipment is not coupled or run with "in spec" equipment, there's no problem. However, if the couplers have excess vertical motion, this is where a problem can start.


ehulshiz

At Train Mountain they do it much as described above, but they use closed eyes and threaded chain "repair links" (you know the ones).

10 Wheeler Rob

Purpose of safety chains is not for derailments, but to keep rolling stock and a cargo of pasengers from rolling away in the event of a coupler failure or disconect. This is because very few cars have self energized brakes in the hobby.

References