Difference between revisions of "Boiler Construction"

Jump to: navigation, search
(External Links)
(External Links)
Line 99: Line 99:
* [https://www.chaski.org/homemachinist/viewtopic.php?f=8&t=105796&hilit=k+type Tube Rollers, <i>Chaski.org</i>]
* [https://www.chaski.org/homemachinist/viewtopic.php?f=8&t=105796&hilit=k+type Tube Rollers, <i>Chaski.org</i>]
* [http://www.elliott-tool.com/support-tools/ Tips on tube rolling and hole preparation, <i>Elliott Tool</i>]
* [http://www.elliott-tool.com/support-tools/ Tips on tube rolling and hole preparation, <i>Elliott Tool</i>]
* [https://www.chaski.org/homemachinist/viewtopic.php?f=8&t=104865 "Reaming vs. Drilling Holes In Tube Sheets", <i>Chaski.org</i>]

Latest revision as of 13:17, 21 March 2020

Soft Solder vs Bronze Welding

by L.B.S.C.

The Live Steamer, May-June 1950

Question: Is a boiler safe to use if it is sweated at the joints, tubes and stays with soft solder?

Answer: Whilst a boiler can be safe to use with riveted and soldered joints, it rapidly deteriorates and eventually leaks. The reason is that the solder gets hard, just like the whitemetal in the big ends of an automobile engine, and presently cracks under the stresses of continued expansion and contraction. Also, a riveted boiler can never be as strong as a brazed or bronze-welded one, for this reason: The perforations where the rivets go thru weaken the plates just like the perforations in a sheet of postage stamps; and given sufficient stress, the plate would tear along the line of holes, just like you can tear the sheet of stamps. This was the cause of several boiler explosions in the early days of steam locomotives.

It is many years ago that I abandoned riveting, except for just a few needed to hold the parts of a boiler together while bronze-welding. In my experience, the most satisfactory construction is all bronze-welded seams, and silver-soldered flues. Thinner metal can be used, with a greater factor of safety, than if the joints are riveted and sweated.

Smaller Loco, Lower Pressure

Karl Friedrick

2039 5th Ave

Pittsburgh 19, PA

The North American Live Steamer, Volume 1 Number 4

Just a few words about steam pressures in small engines. That is, engines with boilers 5 inches or less in diameter. In my opinion, a lot of the fellows are using pressures entirely too high. 100 to 125 pounds is much more than can be used efficiently on the average small locomotive. Most of these little fellows can get along quite nicely on 60 to 75 pounds, and even less if superheated. In my experience and observation, I have come to the conclusion that a superheated job at 60 pounds will do about as well and maybe better than a wet steamer at 90 or 100. Also, the 100+ pressures are liable to cause many little leaks to develop around glands and fittings. The only thing to be gained by higher pressures is that they tend to cancel out defects in workmanship, etc., by sheer brute force.

Tube Sheet

From "Reaming vs. Drilling Holes In Tube Sheets", Chaski.org:

Question: I am working on building a steel boiler with copper tubes. The tubes will be 1/2 inch type K copper, with an O.D. of 0.625 inch. If I use a 16 mm drill for the tube sheets (16mm = 0.6299 inch) this would yield about 0.005 inch oversize on the holes. Some clearance is a good thing, although I recognize that a drill is not as precise as a reamer. A drill would also give a somewhat rougher finish than a reamer, which may (or may not) be desirable to key in the tubes after rolling (?) I would appreciate any comments on this.
Answer: Welding of the tube sheet is likely to distort the drilled holes in proximity of the weld(s). Also, drills have a nasty habit of cutting less than round holes, which may or may not be straight, or on size. While reamers, too, can yield similar errors, they're reduced drastically, so the end result would be more reliable, plus any distortion of hole diameter due to welding would be eliminated.
If you must drill and not ream, don't drill the hole with the target diameter drill. Drill undersized, then open the hole with the proper sized drill after the boiler has been welded. That's not as good as reaming (or boring), but it will yield more consistent hole size, and likely a better surface finish.

Boiling mechanics

There are three types of boiling.

Read more here:

Magazine Articles

External Links