Steam Regulator - Revision history

Dnevil at 17:59, 8 September 2015

2015-09-08T17:59:48Z

@@ Line 30: / Line 30: @@
 </gallery>
-Here is a commercially made version of the regulator, as listed on eBay.  Made from lost wax bronze castings, machined brass, and stainless hardware. Overall length of unit is approx. 2" x 1 3/4" diameter.  Steam inlet is machined with 1/8" NPT thread. Outbound discharge is 3/16" Model taper pipe female threads. Regulate flow of air or steam by turning brass screw.
+== Railroad Supply Version ==
 <gallery widths="300px" heights="300px">
@@ Line 38: / Line 40: @@
 File:Steam regulator commercia 4.jpg
 </gallery>

Dnevil at 13:45, 24 July 2013

2013-07-24T13:45:53Z

@@ Line 28: / Line 28: @@
 File:CharlesReiter SteamRegulator drawing page1.jpg
 File:CharlesReiter SteamRegulator drawing page2.jpg
 </gallery>

Dnevil at 14:55, 29 May 2013

2013-05-29T14:55:58Z

← Older revision		Revision as of 09:55, 29 May 2013
Line 7:		Line 7:
	by Charles P. Reiter		by Charles P. Reiter

	This is a design that has been used around the Golden Gate Live Steamers for a long time. The origin of this design has been lost, but a reprint of a 1953 Miniature Locomotive Magazine article appeared in Live Steam Magazine in May 1986 and is essentially the same unit, although not as refined and lacking dimensions. It was recommended for controlling turbo generators but works equaly well for diesel fuel atomizers. We should thank those who have gone before us and worked out the details.		This is a design that has been used around the [[Golden Gate Live Steamers]] for a long time. The origin of this design has been lost, but a reprint of a 1953 Miniature Locomotive Magazine article appeared in [[Live Steam Magazine]] in May 1986 and is essentially the same unit, although not as refined and lacking dimensions. It was recommended for controlling turbo generators but works equaly well for diesel fuel atomizers. We should thank those who have gone before us and worked out the details.

	With a few scrawlings on several photocopies, gradually the design has evolved and I have endeavored to filter it all and make a real drawing anyone can follow. This is a summation of the tinkerings of several people, so different pipe entry / exit points and mounting details are shown. In the steam industry this device is known as a pressure reducing valve, but I refer to it as a regulator.		With a few scrawlings on several photocopies, gradually the design has evolved and I have endeavored to filter it all and make a real drawing anyone can follow. This is a summation of the tinkerings of several people, so different pipe entry / exit points and mounting details are shown. In the steam industry this device is known as a pressure reducing valve, but I refer to it as a regulator.

Dnevil at 14:30, 29 May 2013

2013-05-29T14:30:14Z

← Older revision		Revision as of 09:30, 29 May 2013
Line 24:		Line 24:

	The body of the regulator is of course steam temperature so an insulated control knob is much safer. It's a good idea to build in a gage into the system, and of course use a siphon.		The body of the regulator is of course steam temperature so an insulated control knob is much safer. It's a good idea to build in a gage into the system, and of course use a siphon.

			<gallery widths="300px" heights="300px">
			File:CharlesReiter SteamRegulator drawing page1.jpg
			File:CharlesReiter SteamRegulator drawing page2.jpg
			</gallery>

Dnevil: Created page with "Category:Construction From [http://web.archive.org/web/20070925130835/http://www.ggls.org/Regulator/index.html www.ggls.org on Archive.org] '''STEAM REGULATOR''' by Cha..."

2013-05-29T14:27:02Z

Created page with "Category:Construction From [http://web.archive.org/web/20070925130835/http://www.ggls.org/Regulator/index.html www.ggls.org on Archive.org] '''STEAM REGULATOR''' by Cha..."

New page

[[Category:Construction]]

From [http://web.archive.org/web/20070925130835/http://www.ggls.org/Regulator/index.html www.ggls.org on Archive.org]

'''STEAM REGULATOR'''

by Charles P. Reiter

This is a design that has been used around the Golden Gate Live Steamers for a long time. The origin of this design has been lost, but a reprint of a 1953 Miniature Locomotive Magazine article appeared in Live Steam Magazine in May 1986 and is essentially the same unit, although not as refined and lacking dimensions. It was recommended for controlling turbo generators but works equaly well for diesel fuel atomizers. We should thank those who have gone before us and worked out the details.

With a few scrawlings on several photocopies, gradually the design has evolved and I have endeavored to filter it all and make a real drawing anyone can follow. This is a summation of the tinkerings of several people, so different pipe entry / exit points and mounting details are shown. In the steam industry this device is known as a pressure reducing valve, but I refer to it as a regulator.

This is an assembled view of a regulator.

[[File:CharlesReiter SteamRegulator drawing.jpg|thumb|center|300px]]

The goal of this device is to regulate the flow of steam to some appliance. It is effectively, a calibrated leak. The oriface at the end of the output pipe is where pressure escapes to the atmosphere. All pressure in the system after the regulator is due to the restriction of this orifice. In full size practice the regulator output pipe is always a larger size, because there is expansion of steam and a reduction in steam temperature.

When the pressure rises in front of the diaphragm, the valve ball closes the orifice down holding flow/ pressure down. When the pressure in the diaphragm chamber lowers, the spud pushes the ball off its seat to allow more to flow. This all happens instantaneously, within a small window of operation, with very little motion. The spring pressures and the stiffness of the diaphragm all contribute to the balanced action of the system.

It can easily be seen that the system is dependent on this balanced action and tightening the control too much or too little will take the system way out of equilibrium. It is also necessary to have a minimum operating pressure over the output pressure but in locomotive use this should be no problem.

All the materials used should be non-corroding in the presence of high temperature steam. The diaphragm should be stainless and if different spring material is used, the springs will need to be redesigned. The large spring is always dry so steel is OK here. The small spring is just there to keep the ball against the seat and its tension is not critical, as long as it closes to slow enough flow. Remember this is a regulator not a valve, so in your plumbing install a control/ shutoff valve ahead of the regulator. To make the diaphragm, a .003 thickness of stainless is sandwiched between two pieces of 0.25 aluminum or other and turned to size. It might be good to make a spare at the same time. This fixturing also helps in drilling the center and peripheral holes.

The body of the regulator is of course steam temperature so an insulated control knob is much safer. It's a good idea to build in a gage into the system, and of course use a siphon.